King's Quest VI CD
Troubleshooting Guide 
for PC's using DOS 5.0 or higher, Windows 3.1 
or Windows 95
revised 12/28/95


Sierra Technical Support provides this documentation as a reference to 
Sierra customers using Sierra software products.  Sierra Technical 
Support makes reasonable efforts to ensure that the information contained 
in this documentation is accurate.  However, Sierra makes no warranty, 
either express or implied, as to the accuracy, effectiveness, or 
completeness of the information contained in this documentation.

SIERRA ON-LINE, INC. DOES NOT WARRANTY OR PROMISE 
THAT THE INFORMATION HEREIN WILL WORK WITH ANY OR 
ALL COMPUTER SYSTEMS.  SIERRA DOES NOT ASSUME ANY 
LIABILITY, EITHER INCIDENTAL OR CONSEQUENTIAL, FOR 
THE USE OF THE INFORMATION HEREIN, INCLUDING ANY 
AND ALL DAMAGE TO OR LOST USE OF COMPUTER 
HARDWARE OR SOFTWARE PRODUCTS, LOSS OF 
WARRANTIES, OR LOST DATA BY THE CUSTOMER OR ANY 
THIRD PARTY.  NO ORAL OR WRITTEN INFORMATION OR 
ADVICE GIVEN BY SIERRA, ITS EMPLOYEES, DISTRIBUTORS, 
DEALER OR AGENTS SHALL CHANGE THE RESTRICTION OF 
LIABILITY OR CREATE ANY NEW WARRANTIES.  IN NO CASE 
SHALL SIERRA'S LIABILITY EXCEED THE PURCHASE PRICE 
OF THE SIERRA SOFTWARE PRODUCT.


TABLE OF CONTENTS

SECTION 1 - HARDWARE REQUIREMENTS
SECTION 2 - INSTALLATION PROCEDURES
SECTION 3 - COMMON INSTALLATION PROBLEMS
SECTION 4 - COMMON GAME PROBLEMS
SECTION 5 - RUNNING THE GAME UNDER WINDOWS 95
SECTION 6 - SOUND CARD CONFIGURATION AND SOUND ISSUES
SECTION 7 - DOS OR WINDOWS 3.1 BOOT DISK INSTRUCTIONS
SECTION 8 - WINDOWS 95 BOOT DISK INSTRUCTIONS
SECTION 9 - IF YOU STILL HAVE PROBLEMS
SECTION 10 - SOUND CARD DRIVER INFORMATION

SECTION 1 - HARDWARE REQUIREMENTS

REQUIRED:

386 SX
2 MB RAM
575k free conventional memory
CD-ROM drive
Small Install: 1MB hard drive space (2 MB compressed) 
Large Install: 16MB hard drive space (32 MB compressed)
MS-DOS 5.0 or higher for DOS version
Windows 3.1 or Windows 95 for Windows version
640 x 480 x 256 colors for Windows resolution


RECOMMENDED FOR BEST PERFORMANCE:

486 or higher
4 MB RAM
Double Speed CD-ROM Drive
Sound Card with DAC


SECTION 2 - INSTALLATION PROCEDURES

DOS: 
Insert the CD and switch to the CD drive by typing the drive letter 
followed by a colon. Ex: D:.  Then type INSTALL to begin the 
installation program.  Follow the on-screen prompts to complete the 
installation.  

WINDOWS 3.1:
Insert the CD into the appropriate drive.  From Program Manager, click 
on File, then Run.  In the Command Line field, type the letter of the drive 
followed by \SETUP.  Ex: D:\SETUP.  Follow the on-screen prompts to 
complete the installation.

WINDOWS 95:
Insert the CD into the appropriate drive. Click on the Start Button, then 
Run.  In the Open field, type the letter of the drive followed by \SETUP.  
Ex: D:\SETUP.  Follow the on-screen prompts to complete the 
installation.


SECTION 3 - COMMON INSTALLATION PROBLEMS

DOS AND WINDOWS:
PROBLEM: During installation you receive the error "DISK ERROR / 
READ ERROR" or "NOT READY READING DRIVE X" (Where X is 
the drive you are installing from).
SOLUTION: This usually indicates a bad disk.  If you have had the product 
less than 90 days, Sierra will replace your game disks for free.  Send Disk 
#1 with a copy of a dated receipt and a letter requesting disk replacement.  
Be sure to include your  full name, mailing address and a phone number.  
If you have had the product over 90 days you will need to include a check 
or money order for $10.00.  The address is: Sierra On-Line Fulfillment, 
PO Box 485, Coarsegold, CA  93614-0485.

DOS ONLY:
PROBLEM:  After typing INSTALL, a row of dots goes across the screen 
and stops.  The computer is locked up with this row of dots appearing on 
the screen.
SOLUTION:  The dots indicate the hardware detection portion of the 
installation program.  You can bypass the hardware detection (and 
therefore the lockup) by typing INSTALL /M.  If this entry doesn't work, 
try INSTALL /F.  One of these entries should get you past the lockup. If 
these alternate INSTALL commands do not correct the problem, create a 
boot disk using the boot disk instructions in Section 6 and install the game 
under the boot disk environment. 

WINDOWS ONLY:
PROBLEM:  You receive an error message stating, "Your current display 
driver is not supported by this game."
SOLUTION:  Sierra's Windows games require that Windows is running in 
256 color mode.  Running Windows in less or more colors will cause this 
error message. The following instructions should help you change your 
Windows video resolution to 256 colors:

Windows 3.1
Double-click on Windows Setup in the Main program group. If the 
Display line reads "64,000", "32 million", "VGA" or "16 color", you will 
need to change to a driver that supports 256 colors.  ("VGA" is a default 
Windows video driver that only supports 16 colors and will not work with 
Sierra's Windows games.)  To change video drivers, select Options, then 
Change System Settings.  Open the Display box to see the list of video 
drivers that are currently available.   You should check your video card 
documentation for information on what 256 color driver to select.  

Be careful when changing video drivers!  If you choose one that is not 
designed for your particular video card, Windows will not display 
properly.  If this occurs, change to your Windows directory, type: 
SETUP, and choose the "VGA" driver again.  You should contact your 
video card manufacturer for the correct driver.

Windows 95
Click on the Start button, select Settings, then Control Panel. Double-
click the Display icon. You will see four tabs: Background, Screen 
Saver, Appearance, and Settings. Click on Settings. In the box under 
Color Palette, it should say 256 Color. If it does not, click on the down 
arrow next to the window to view a list of choices, and select the one that 
says 256 Color. Restart Windows when prompted to do so. If you have 
any trouble running Windows 95 in 256 color mode, please contact your 
video card manufacturer for assistance. 


SECTION 4 - COMMON GAME PROBLEMS

Unless otherwise stated, the following issues can occur in both the DOS 
and Windows version of King's Quest VI.

PROBLEM: When you attempt to run the game, you receive an error 
message indicating insufficient memory. 
SOLUTION: Create a boot disk using the instructions in Section 7 or 8 and 
run the game under the boot disk environment. This should free up enough 
memory to run the game. 

PROBLEM:  The game locks up after the first sound effect is played. (DOS 
version.)
SOLUTION:  This usually occurs with Soundblaster 16 and compatible 
sound cards. To correct this, run the game's INSTALL program, and 
choose Soundblaster/Adlib for Music and Thunderboard for 
Speech/Audio. 

PROBLEM:  When you start the game you see a black screen with the main 
character(s), and as you move the character the screen clears. (Windows 
version)
SOLUTION:  You are running in a resolution that uses higher than 256 
colors.  See Section 3 for changing your display driver.

PROBLEM:  When the characters are talking, the area around their mouth is 
distorted. (Windows version)
SOLUTION:  If you have an ATI Ultra Graphics Pro video card, you have a 
program called Flex Desk.  To solve this problem turn Device Bitmap 
Draw off in the Flex Desk application. If you have any other video card, 
contact the card manufacturer to obtain updated Windows video drivers. 

PROBLEM:  "Out of Hunk" or "Insufficient Memory" messages. 
SOLUTION:  Follow the appropriate instructions in Sections 7 or 8 for 
making a boot disk.

Windows 95 Only
PROBLEM:  The icon for the game doesn't look like the King's Quest 6 icon 
(e.g.- it looks like the Phantasmagoria icon).
SOLUTION:  Go into Windows Explorer to the Sierra\KQ6CD directory and 
change the name of the icon from SIERRAW.ICO to KQ6.ICO and then 
change the icon.  Consult your Windows 95 manual for instructions on 
changing your icon.


SECTION 5 - RUNNING KING'S QUEST VI UNDER WINDOWS 95

The following basic troubleshooting steps should help you resolve 
problems such as memory errors, crashes, lockups and illegal instruction 
errors (GPFs).

Step 1 - Run the program from a minimal boot disk.  
Memory conflicts are a common cause of problems with games in the 
Windows 95 environment. Creating a boot disk will free up more system 
resources and memory for your games.  The boot disk also creates an 
environment that is "cleaner" or free of extra TSR and utilities that can 
sometimes cause conflicts. Detailed boot disk instructions are included in 
Section 2 of this document.

Step 2 - Check for corrupted files and hard drive errors.
Windows 95 contains a program called Scandisk that will check your hard 
drive for errors. To run Scandisk, click on Start, Programs, Accessories, 
System Tools and choose Scandisk from the list.  If Scandisk finds any 
errors on the hard drive, fix them, then delete your game and reinstall it. 

Step 3 - Check your sound card drivers.
Windows 95 ships with many sound card drivers, however, there are 
many sound cards are not directly supported.  When a sound card is not 
directly supported by Windows 95, the game may lock up or crash. Check 
with your sound card manufacturer to see if they have Windows 95 
drivers. If no Windows 95 drivers are available, running the game in MS-
DOS mode may correct the problem. 

Step 4 - Reinstall the game in a clean boot environment.  
Lockups and other technical problems can be caused by corrupted game 
files.  No program will run correctly if the data or executable files are 
corrupted.  These corruptions will occur during the installation of the 
game and are usually due to conflicts with TSRs or other utilities running 
during the game installation. You should install the game in a "clean" boot 
environment. See Section 8 for complete instructions on creating a boot 
disk.

Step 5 - Create a clean Windows environment.
Make sure that all screen savers, virus scans, and sound-related Windows 
programs (IconHear It, Wired for Sound, etc.) are disabled before starting 
the game. You should also check to make sure that you have virtual 
memory enabled. You can check this by clicking on Start, Setting, 
Control Panel, System, Performance, Virtual Memory.   Make sure 
that Let Windows manage my virtual memory settings is checked. 

Step 6 - Check your CD-ROM drivers.
Windows 95 ships with the most common CD ROM drivers, however, 
there are some CD ROM drives out there that Windows 95 does not 
support directly.  If you are having trouble reading CD's, check with your 
CD ROM drive manufacturer to find out what lines need to appear in 
your CONFIG.SYS and AUTOEXEC.BAT. 


SECTION 6 - SOUND CARD CONFIGURATION AND SOUND ISSUES

DOS SOUND CARD CONFIGURATION
In DOS, the best sound card settings for a SoundBlaster compatible card 
are I/O 220, DMA 1 and IRQ 5 or 7.  If you're using a Pro Audio card, 
the best settings are I/O 220, DMA 3 and IRQ 5 for the Pro Audio portion 
of the card, set the SoundBlaster portion of the card to DMA 1 and IRQ 
7.  Make sure that the SoundBlaster and ProAudio portions do not share 
the same DMA!  Settings outside these parameters can cause lockups 
and/or choppy, repeating or garbled speech.   Most sound cards have test 
utilities that will tell you what settings you are using.  Check your sound 
card documentation for more information.

WINDOWS 3.1 SOUND CARD CONFIGURATION
Sierra's Windows games should work correctly with any sound card 
setting, providing there are no hardware conflicts. However, as in DOS, 
Sierra recommends using the sound card's default settings.  When 
configuring your sound card in Windows, there are two locations to check: 
the Drivers section of Control Panel and the MIDI Mapper. 

In the Drivers section, you should see the following:

MIDI Mapper
Timer
[MCI] CD Audio
[MCI] MIDI Sequencer 
[MCI] Sound

These drivers come with Windows, so if you are missing any, they can be 
installed by choosing the Add button in the Drivers window and installing 
them off of your Microsoft Windows Installation disks. In addition to 
these standard Windows drivers, there should be two or three sound card-
specific drivers.  These drivers should have the name of your sound card 
in their title. If these are missing, you will need to reinstall the sound card 
drivers off of the sound card installation disks. Your sound card 
documentation will tell you the names of these drivers and how to install 
them. 

The MIDI Mapper should be set to "All FM" or something similar if you 
have a SoundBlaster Pro, SoundBlaster 16, Pro Audio 16 or compatible 
card. If your MIDI Mapper doesn't have an "All FM" option, you will 
need to make a new MIDI Mapper setup.  From the MIDI Mapper screen, 
click on New.  Enter a name such as "Test" or "All FM" and then click on 
OK.  You will see a screen with four columns and 16 rows.  Click on the 
word None in the 3rd column and the 1st row.  Now click on the small 
arrow that appears on the right of this box.  Choose the FM choice or 
Synthesizer choice.  Do this for ports 1 through 16.  Then, make sure that 
the SRC Channel values match the Dest Channel values (i.e. if the SRC 
Channel is 10, the Dest Channel should be 10).  If they are different, 
change the Dest Channel to match the SRC Channel by clicking in the 
Dest Channel box and changing its value.  Click on OK and close out the 
MIDI Mapper. For further information on the correct MIDI Mapper 
configuration for your sound card, please contact your sound card 
manufacturer. 

If you have a General MIDI device, such as a Roland MT-32 or a 
SoundBlaster AWE 32, please consult your sound card documentation or 
contact the sound card manufacturer for the correct MIDI Mapper 
configuration. 


WINDOWS 95 SOUND CARD CONFIGURATION
To make sure that your sound card is configured correctly in 
Windows 95, check the Audio and MIDI settings in the Multimedia 
section of Control Panel.  The Audio setting defines what driver will 
be used to produce digitized sound (DAC). Speech and sound effects 
in a game are usually DAC sounds. The MIDI setting indicates what 
driver is being used for music playback. The following examples are 
for the SoundBlaster 16:

AUDIO: SB16 Wave Out
MIDI: MIDI for Internal OPL2/OPL3 FM Synthesis

The names of the Audio and MIDI drivers will vary, depending on 
your sound card. However, they should be similar to these 
SoundBlaster 16 drivers. For complete information (including driver 
names and installation instructions) on Windows 95 drivers for your 
sound card, contact your sound card manufacturer. 


DOS SOUND ISSUES
PROBLEM:  The game locks up when a character speaks or a sound effect 
is played.
SOLUTION:  This usually happens with SoundBlaster 16 and compatible 
cards.  To fix it, rerun the INSTALL program, change Music to 
SoundBlaster/Adlib and Audio to Thunderboard.  If this does not 
correct the problem, you may be using non-standard sound card settings, 
or have a hard ware conflict; see the Sound Card Settings section of this 
document.

PROBLEM:  Choppy, repeating or garbled speech.
SOLUTION:  This is caused by non-standard sound card settings or a conflict 
between the sound card and another piece of hardware on your computer.  
See "DOS Sound Card Configuration" above for supported settings and 
refer to your sound card documentation for information on resolving 
hardware conflicts.


WINDOWS 3.1 SOUND ISSUES
PROBLEM:  You hear speech but no music.
SOLUTION:   This is caused by an incorrect MIDI Mapper setting. See 
"Windows 3.1 Sound Card Configuration" above for information on 
correctly setting up the MIDI Mapper.

WINDOWS 95 SOUND ISSUES
PROBLEM: No sound or music.
SOLUTION: This may be caused by incorrect driver selection or outdated or 
incompatible sound card drivers. See "Windows 95 Sound Card 
Configuration" above for information on Windows 95 sound card drivers. 



SECTION 7 - DOS OR WINDOWS 3.1 BOOT DISK INSTRUCTIONS

IMPORTANT NOTE: Please read the entire instructions prior to 
starting at Step 1. If you are playing a the Window version of King's 
Quest VI, skip Step 2. 

STEP 1
FORMATTING THE DISK
To make a boot disk, you must system format a high density diskette in 
the A: drive. This procedure will transfer the "system files" to the disk and 
allow the computer to boot up correctly.  The disk must be in the A: drive; 
the computer will not boot from the B: drive. At a DOS prompt, type the 
FORMAT command as follows:

FORMAT A: /S <ENTER>

If you get a "Bad command or file name" error message, type: 

PATH=C:\DOS <ENTER>

Then retype the FORMAT command above.  If you receive the error 
again, the MS-DOS FORMAT command may not be on your system, or 
it may have been renamed.  Programs such as PC Tools and Norton Disk 
Utilities sometimes rename the FORMAT command to prevent accidental 
loss of data.  If you are using a program of this type, check your 
documentation to find out how to format a SYSTEM DISK, then proceed 
to Step 2. 

STEP 2
LOCATING THE MOUSE DRIVER (skip if playing King's Quest VI in Windows)
If you are playing a game that uses a mouse, the Microsoft compatible 
mouse driver must be loaded into memory with the boot disk. There are 
two kinds of mouse drivers available: those that load in the CONFIG.SYS 
file and those that load in the AUTOEXEC.BAT file.  CONFIG.SYS 
mouse drivers have an extension of .SYS (MOUSE.SYS) and 
AUTOEXEC.BAT drivers have either a .COM or .EXE extension 
(MOUSE.COM, MOUSE.EXE).  You must load at least one of these 
drivers, but it is not necessary to load them all. 

If you do not know where the mouse drivers are located on your system, 
the command below should help you locate them.  Type the following at 
the C:\ prompt:

DIR MOUSE* /S <ENTER>

This command will cause the system to search all subdirectories for a file 
called MOUSE.  If the system locates a MOUSE file, it will display the 
path where the file is located.  For example, if the MOUSE.COM file is 
located in a C:\MOUSE directory, the system will display:

Directory of C:\MOUSE
	MOUSE.SYS		55160 	03-10-92	3:10a
	MOUSE.COM		56408	03-10-03	6:00a

If this procedure does not locate a MOUSE file, your mouse driver may 
have a different name; some common names for mouse drivers are 
IMOUSE, GMOUSE and HPMOUSE.  Your should check your mouse 
documentation for the exact file names and how to install them. 

Once you have located the mouse driver, you must copy it to the boot 
disk.  The following example assumes that the mouse drivers are located 
in the C:\MOUSE directory as shown above.  To copy the MOUSE files 
to the boot disk, type:

COPY C:\MOUSE\MOUSE.* A: <ENTER>

Substitute the appropriate path and file names for your mouse drivers in 
the command above.  After you press ENTER, you should see a message 
indicating that some files were copied.


STEP 3
LOCATING THE CD ROM DEVICE DRIVER 
The CD ROM drive requires a device driver loaded in the CONFIG.SYS 
file.  This driver must be loaded correctly or you will be unable to access 
your CD ROM drive. To make sure that the device driver loads correctly 
on the boot disk, look at the CONFIG.SYS on the hard drive and copy the 
driver line from there.  To display the CONFIG.SYS, type the following 
at a DOS prompt:

CD\ <ENTER>
EDIT CONFIG.SYS <ENTER>

The CONFIG.SYS file will display on the screen. Look for the line that 
loads the CD ROM device driver. The line should look something like 
this:

DEVICE=C:\DRV\CDROMDRV.SYS /D:MSCD001 /P:220
DEVICEHIGH=C:\DRV\CDROMDRV.SYS /D:MSCD001 /P:220
DEVICEHIGH /L:14652 =C:\DRV\CDROMDRV.SYS /D:MSCD001 /P:220

The device driver in your CONFIG.SYS may differ slightly from those 
listed above.  Carefully write down the line for use in your boot disk.  

To exit the CONFIG.SYS, press the <ALT>, <F>, then <X> keys.

If you have a SCSI CD ROM drive, there may be an additional driver in 
your CONFIG.SYS that must be loaded for the CD ROM device drivers 
to load correctly.  Check your CD drive documentation for more 
information. 

NOTE:  If you cannot locate the driver in your CONFIG.SYS file, check 
your CD-ROM drive documentation, or contact the drive's manufacturer.

STEP 4
LOCATING THE MSCDEX CD ROM EXTENSION 
In addition to the CD ROM device driver in the CONFIG.SYS, your CD 
ROM drive requires MSCDEX, the Microsoft extension for CD ROM 
drives.  If this extension is not loaded correctly in the AUTOEXEC.BAT, 
you will be unable to access your CD ROM drive. To display the 
AUTOEXEC.BAT, type the following at a DOS prompt:

CD\ <ENTER>
EDIT AUTOEXEC.BAT <ENTER>

The AUTOEXEC.BAT file will display on the screen. Look for the line 
that loads MSCDEX. It should look something like this:

C:\DOS\MSCDEX /D:MSCD001
LH C:\DOS\MSCDEX /D:MSCD001 
LOADHIGH /L:14429 C:\DOS\MSCDEX /D:MSCD001

The MSCDEX line in your AUTOEXEC.BAT may differ slightly from 
the ones above. Carefully write down the line for use in your boot disk.  

To exit the AUTOEXEC.BAT, press the <ALT>, <F>, then <X> keys.

STEP 5
LOCATING THE SOUND CARD DRIVERS
Many sound cards have drivers or initialization lines that must be loaded 
in the AUTOEXEC.BAT or CONFIG.SYS.   Some sound cards that 
require these drivers or initialization routines are the SoundBlaster 16, 
MAD16 and the Aria 16.

At the end of this document, you will find a section labeled "Sound 
Cards".  These tables contain the sound card lines for many common 
sound cards.  Check to see if your sound card is on the list.  If it is, you 
will need to add the appropriate lines to the AUTOEXEC.BAT and/or 
CONFIG.SYS on your boot disk.  If your sound card is not listed, you 
should check your documentation for information on what needs to load in 
the AUTOEXEC.BAT and CONFIG.SYS. 

STEP 6
CREATING THE CONFIG.SYS FILE
To create the CONFIG.SYS file on the boot disk, type the following at a 
DOS prompt:

A: <ENTER>
CD\ <ENTER>
EDIT CONFIG.SYS <ENTER>

This will display the blank (usually blue) screen of the DOS Editor. Enter 
the following lines:

DEVICE=C:\DOS\HIMEM.SYS 
DEVICE=C:\DOS\EMM386.EXE NOEMS (leave this line out if 
you're playing a in Windows)
DOS=HIGH,UMB 
FILES=30
BUFFERS=20 

If you're using MOUSE.SYS to load your mouse, add the following line:

DEVICEHIGH=A:\MOUSE.SYS 

Add the CD ROM device driver as you wrote it down in the "Locating the 
CD ROM Device Driver" section.  If you're playing a standard DOS 
game, the device driver should look something like this:

DEVICEHIGH=C:\DRV\CDROMDRV.SYS /D:MSCD001 /P:220 

If you need to load any sound card drivers, copy them from the "Sound 
Cards" section now.  The following example lines are for the 
SoundBlaster 16:

DEVICEHIGH=C:\SB16\DRV\CTSB16.SYS /UNIT=0 /BLASTER=A:220 I:5 D:1 H:5 
DEVICEHIGH=C:\SB16\DRV\CTMMSYS.SYS

Save the file by pressing <ALT>, <F>, then <S>.  Exit the file by 
pressing <ALT>, <F>, then <X>.

STEP 7
CREATING THE AUTOEXEC.BAT FILE
To create the AUTOEXEC.BAT file on the boot disk, type the following 
at a DOS prompt:

A: <ENTER>
CD\ <ENTER>
EDIT AUTOEXEC.BAT <ENTER>

This will display the blank (usually blue) screen of the DOS Editor. Enter 
the following lines:

@ECHO OFF
C:\ 
SET COMSPEC=C:\COMMAND.COM 
PROMPT SIERRA BOOT DISK $_$P$G 
PATH=C:\;C:\DOS;C:\SIERRA 

If you are using the MOUSE.COM or MOUSE.EXE file to load your 
mouse, add the appropriate line:

LH A:\MOUSE.COM

Add the MSCDEX line as you write it down in the "Locating the 
MSCDEX CD ROM Extension" section.  For example:

LH C:\DOS\MSCDEX /D:MSCD001 

If you are playing in Windows, add the following line:

LH C:\DOS\SMARTDRV

If you need to run any sound card initialization programs or load any 
drivers, copy them from the "Sound Cards" section now.  The following 
example lines are for the SoundBlaster 16:

SET BLASTER=A220 I5 D1 H5 T6 
SET SOUND=C:\SB16
SET MIDI=SYNTH:1 MAP:E 
C:\SB16\SB16SET /M:220 /VOC:220 /CD:220 /MIDI:220 /LINE:220 
C:\SB16\DIAGNOSE /S 

Save the file by pressing <ALT>, <F>, then <S>.  Exit the file by 
pressing <ALT>, <F>, then <X>.

STEP 8
REBOOT THE COMPUTER AND START THE GAME
Reboot your system by pressing the <RESET> button on your computer 
or by using the <CTRL> <ALT> <DELETE> key sequence on your 
keyboard.  Follow the instructions in the game manual to start the game.


SECTION 8 - BOOT DISK INSTRUCTIONS FOR WINDOWS 95

IMPORTANT NOTE:  Please read all instructions before beginning this 
procedure.

STEP 1
FORMATTING THE DISK
To make a boot disk, you must system format a high density diskette in 
the A: drive. This procedure will transfer the "system files" to the disk and 
allow the computer to boot up correctly.  The disk must be in the A: drive; 
the computer will not boot from the B: drive. 

To format a disk in Windows 95, put the disk in the drive, open My 
Computer, then right click on the A: icon. From the pop-up menu, select 
Format. Under "Format type" select Full; under "Other options", choose 
Copy system files. Click on Start. 

After the disk is formatted, you must copy the MSDOS.SYS file from the 
hard drive to the floppy disk.  To do this, leave the floppy disk in the 
drive, open Windows Explorer and find the MSDOS.SYS file in the root 
of the C: drive.  Right click on the file, then select Send to from the pop-
up menu.  Send the file to the A: drive. 

NOTE:  If you don't see the MSDOS.SYS file in Explorer, the file is 
hidden.  To make the file visible, select View, Options, then Show all 
files. If you do not wish the hidden files to remain visible, you can hide 
them again after you've made the boot disk by choosing View, Options, 
Hide files of this type.

STEP 2 
LOCATING THE CD ROM DEVICE DRIVER
The CD ROM drive may require a device driver loaded in the 
CONFIG.SYS file. Look at the CONFIG.SYS on your hard drive to 
determine if you need to load a CD ROM driver on the boot disk. To 
display the CONFIG.SYS, click on the Start button, then choose Run.  In 
the Open line, type SYSEDIT, then click on OK.  The SYSEDIT 
window will appear.  Click on the CONFIG.SYS title bar to display the 
CONFIG.SYS file. Look for a line that loads a CD ROM device driver. 
The line will look something like this:

DEVICE=C:\DRV\CDROMDRV.SYS /D:MSCD001 /P:220
DEVICEHIGH=C:\DRV\CDROMDRV.SYS /D:MSCD001 /P:220
DEVICEHIGH /L:14652 =C:\DRV\CDROMDRV.SYS /D:MSCD001 /P:220

The device driver in your CONFIG.SYS may differ slightly from those 
listed above. Carefully write down the line for use in your boot disk. If 
you do not see a CD ROM driver line, then Windows 95 supports your 
CD drive directly and it is not necessary to add a CD driver line to your 
boot disk. 

NOTE: Native support of CD ROM drives is only available when booting 
to Windows 95. When you boot to DOS mode, you will need to load a CD 
ROM driver in the CONFIG.SYS. Check your CONFIG.SYS on your 
hard drive for the appropriate driver. If you do not see a driver in the 
CONFIG.SYS file, check the CONFIG.DOS file. If you still cannot locate 
the correct driver, contact the CD ROM drive manufacturer or consult 
your documentation.

STEP 3
LOCATING THE MSCDEX CD ROM EXTENSION (May be 
optional - see note below.)
NOTE: The MSCDEX line is necessary when running games in DOS 
mode, or when your CD ROM drive is not supported directly by Windows 
95.

In addition to the CD ROM device driver in the CONFIG.SYS, your CD 
ROM drive requires MSCDEX, the Microsoft extension for CD ROM 
drives. To make sure that MSCDEX loads correctly on the boot disk, use 
SYSEDIT to look at the AUTOEXEC.BAT on your C: drive and copy the 
MSCDEX line from there.  It should look something like this:

C:\WINDOWS\COMMAND\MSCDEX /D:MSCD001
LH C:\WINDOWS\COMMAND\MSCDEX /D:MSCD001 
LOADHIGH /L:14429 C:\WINDOWS\COMMAND\MSCDEX /D:MSCD001

The MSCDEX line in your AUTOEXEC.BAT may differ slightly from 
the ones above. Carefully write down the line for use in your boot disk.  

If you cannot find the MSCDEX line in the AUTOEXEC.BAT file, then 
most likely you do not need to load it to access your CD ROM drive in 
Windows 95. Skip this step and continue to Step 4.

STEP 4
CREATING THE CONFIG.SYS FILE
To create the CONFIG.SYS file on the boot disk, choose Start, Run, then 
type NOTEPAD A:\CONFIG.SYS in the command line field. This will 
start the Windows Notepad program. In the new Notepad screen, enter the 
following lines:

DEVICE=C:\WINDOWS\HIMEM.SYS
DOS=HIGH,UMB
FILES=30
BUFFERS=20 

If you're booting to DOS mode and are using MOUSE.SYS to load your 
mouse, add the following line:

DEVICEHIGH=A:\MOUSE.SYS 

If you need to load a CD ROM device driver, add the line from "Locating 
the CD ROM Device Driver" section. The device driver should look 
something like this:

DEVICEHIGH=C:\DRV\CDROMDRV.SYS /D:MSCD001 /P:220 

If you need to load any sound card drivers, copy them from the "Sound 
Cards" section now.  The following example lines are for the 
SoundBlaster 16:

DEVICEHIGH=C:\SB16\DRV\CTSB16.SYS /UNIT=0 /BLASTER=A:220 I:5 D:1 H:5 
DEVICEHIGH=C:\SB16\DRV\CTMMSYS.SYS

Save the file by clicking on File, Save.  Close Notepad by clicking on 
File, Exit.

STEP 5
CREATING THE AUTOEXEC.BAT FILE
To create the AUTOEXEC.BAT file on the boot disk, choose Start, Run, 
then type NOTEPAD A:\AUTOEXEC.BAT in the command line field. 
This will start the Windows Notepad program. In the new Notepad screen, 
enter the following lines:

@ECHO OFF
C:\ 
SET COMSPEC=C:\COMMAND.COM 
PROMPT SIERRA BOOT DISK $_$P$G 
PATH=C:\;C:\WINDOWS;C:\WINDOWS\COMMAND;C:\DOS

If your CD ROM drive requires the MSCDEX CD-ROM extension, add 
the line loading MSCDEX that you wrote down in Step 3.

Save the file by clicking on File, Save.  Close Notepad by clicking on 
File, Exit.

STEP 6
REBOOT THE COMPUTER AND RUN THE GAME
Leave the disk in the drive and restart the computer by clicking on Start, 
Shut Down., then Restart the computer or Restart the computer in 
MS-DOS mode. The computer will now re-boot with the boot disk. When 
Windows 95 restarts, start your game.


SECTION 9 - IF YOU STILL HAVE PROBLEMS...

If you continue to experience problems, or if you have any questions 
concerning any of the above steps, Sierra Technical Support will be happy 
to assist you.  You can reach Technical Support at (206) 644-4343 
between 8:15 am and 4:45 pm, Monday through Friday.  We can also be 
reached by fax at (206) 644-7697 or by mail at the following address:

Sierra On-Line Technical Support
PO Box 85006
Bellevue, WA  98015-8506

In Europe, please contact our office in England. The Customer Service 
number is (44) 1734-303171, between 
9:00 am and 5:00 pm, Monday through Friday.   The BBS number is (44) 
1734-304227 and the fax number 
is (44) 1734-303201.  Customer Service can also be reached at the 
following address:

Sierra On-Line Limited
4 Brewery Court
The Old Brewery
Theale, Reading, Berkshire
RG7 5AJ UNITED KINGDOM


You can also contact our Technical Support Team on one of the following 
services:

Sierra BBS		(206) 644-0112 (settings 8, N, 1, up to 14.4)
CompuServe		GO SIERRA
America Online		KEYWORD SIERRA
Internet			support@sierra.com
			http://www.sierra.com


If you decide to write or fax, please provide the following information so
that Sierra Technical Support can assist you as efficiently as possible:

Name:
Fax number:
Phone number:
Address:

Game name, version number and S/N number (from disk #1 or CD hub): 

What problem are you having?  Be VERY specific.  Is there an 
error message?  What is it?  Where does it occur? Does it happen 
the same way each time?





Floppy or CD?

Are you playing in Windows or DOS?

Type of computer (386, 486, etc.)

Brand of video card (Trident, Diamond, etc.)

Amount of RAM (4 meg, 8 meg, etc.)

DOS version (MS-DOS 6.0, PC-DOS 6.2, etc.)

Windows version (3.1, WFWG, Win95, etc.)

Brand of sound card and sound card settings (SoundBlaster Pro, 
Forte16, Mozart, etc.  Please be VERY specific with the brand 
name. Sound card settings include DMA, IRQ and I/" values.)

Any disk compression?  What kind? (Doublespace, Stacker, etc.)

Any third-part memory manager?  What kind?  (QEMM, 386MAX, 
etc.)

Largest executable program size or bytes free after booting with the 
boot disk. (Type MEM to find out.) 

What have you tried so far?  (Boot disk, no sound, etc.)



Please attach copies of your CONFIG.SYS and AUTOEXEC.BAT 
from your hard drive and the boot disk.

                              

SOUND CARD DRIVER INFORMATION 

NOTE:  The sound card drivers and initialization lines in this section are
the default settings for these devices.  You should check your AUTOEXEC.BAT
and CONFIG.SYS on your hard drive to see if you are using any non-default
settings.


ADLIB
        AUTOEXEC.BAT
        NONE

        CONFIG.SYS
        NONE

This is a MIDI card only and will not play most sound 
effects.


ARIA 16 - Common on IBMs
        AUTOEXEC.BAT
        SET ARIA=C:\ARIA
        SET BLASTER=A220 I5 D1 T5
        C:\DOS\SOUNDCLT.COM*

        CONFIG.SYS
        DEVICE=C:\ARIA\BIN\SOUNDCFG.SYS
        DEVICE=C:\ARIA\BIN\SNDSAVER.SYS
        
*This line is not always present.


ATI STEREO FXCD
        AUTOEXEC.BAT
        SET ATI_SND=C:\SFXCD

        CONFIG.SYS
        NONE


AUDIO ROCK IT 16
        AUTOEXEC.BAT
        NONE

        CONFIG.SYS
        NONE


AUDIO 16 BY AZTECH
        AUTOEXEC.BAT
        C:\GB2KAUDIO\UTILITY\GWBVOL
        SET BLASTER=*
        SET SOUND=*

        CONFIG.SYS
        NONE

*Check your AUTOEXEC.BAT on the hard drive for
the SET BLASTER and SET SOUND parameters.


BOCA SOUND EXPRESS
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1 T5

        CONFIG.SYS
        DEVICE=C:\SE1440\CSACMOD1.EXE


BREVE TECHNOLOGIES
        AUTOEXEC.BAT
        C:\BRV16F\DOSDRV\INIT16
        C:\BRV16F\DOSDRV\MIXER

        CONFIG.SYS
        NONE


CRYSTAL CLEAR WAVE TABLE BY CRYSTAL LAKE
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1 T5
        C:\CCLEAR\CSACMAX1.COM*
        C:\CCLEAR\CSACHMX1.COM**

        CONFIG.SYS
        DEVICE=C:\CCLEAR\CSAMOD1.EXE -S***

*Enables Soundblaster compatibility.
**Add /ON to enable Soundblaster compatibility, /OFF to disable it.
***Use -S for Soundblaster mode and -W for Windows Sound System mode.


DIAMOND
        AUTOEXEC.BAT
        SET BLASTER=*
        SET SOUND16=C:\DIAMOND
        C:\DIAMOND\SNDINIT /B**

        CONFIG.SYS
        NONE

*Check your AUTOEXEC.BAT on the hard drive for the SET BLASTER parameters.
**Use /C for Soundblaster mode and /B for Microsoft Sound System mode.


DIAMOND LX
        AUTOEXEC.BAT
        SET SOUND=C:\SONIC
        SET BLASTER=A220 I5 D1 T5
        C:\SONIC\MZTVOL.EXE
        C:\SONIC\MZTINIT WSS*
        C:\SONIC\MTZINIT.SYS

        CONFIG.SYS
        NONE

*Use WSS for Windows Sound System mode and SB for Soundblaster mode.


DSP16
        AUTOEXEC.BAT
        SET BLASTER=*

        CONFIG.SYS
        NONE

*Check your AUTOEXEC.BAT on the hard drive for the SET BLASTER parameters.


ENSONIQ SOUNDSCAPE - Common on Gateways
Driver version 1.10 dated 11/31/94
        AUTOEXEC.BAT
        SET BLASTER=A220 Ixx Dx
        SET SNDSCAPE=C:\SNDSCAPE
        C:\SNDSCAPE\SSINIT FM*
        C:\SNDSCAPE\VSB_EMM.COM**

        CONFIG.SYS
        DEVICE=C:\DOS\EMM386.EXE***

*Use FM for FM synth, GM for General MIDI and MT32 for Roland MT32 emulation.
**Can help with Soundblaster emulation. Requires the EMM386 line in the CONFIG.SYS
***Necessary for the VSB_EMM.COM line in the AUTOEXEC.BAT


ENSOMIQ SOUNDSCAPE - Common on Gateways
Driver version 1.20.02 dated 12/19/94
        AUTOEXEC.BAT
        SET BLASTER=A220 Ixx Dx
        SET SNDSCAPE=C:\SNDSCAPE
        C:\SNDSCAPE\SSINIT /I*
        C:\SNDSCAPE\VSB_EMM.COM**

        CONFIG.SYS
        DEVICE=C:\DOS\EMM386.EXE***

*/I enables FM synth and General MIDI emulation.
Run MT32.EXE to enable Roland MT32 emulation.
**Can help with Soundblaster emulation. Requires the EMM386 line in the CONFIG.SYS
***Necessary for the VSB_EMM.COM line in the AUTOEXEC.BAT


ESS AUDIO DRIVE - Common on Compaqs
        AUTOEXEC.BAT            
        NONE     

        CONFIG.SYS
        DEVICE=C:\CPQDOS\VOLCTRL.EXE*
        DEVICE=C:\PCAUDIO\VOLCTRL.EXE**

*Loads the DOS mixer. <Ctrl/Right Shift> turns up the volume, <Ctrl/Left Shift>
turns it down.
**Necessary to load Windows mixer.


FORTE 16 - Common on Packard Bells
        AUTOEXEC.BAT
        SET BLASTER=*
        SET GALAXY=*
        SET SOUND=C:\FORTE16
        C:\FORTE16\UTILITY\EMUTSR

        CONFIG.SYS
        NONE

*Check the AUTOEXEC.BAT on your hard drive for these settings.
**Enables the Soundblaster emulation.


FUSION 16
        AUTOEXEC.BAT
        SET BLASTER=*

        CONFIG.SYS
        DEVICE=C:\SPECTRUM\MVSOUND.SYS D: Q:**

*Check the AUTOEXEC.BAT on your hard drive for these settings.
**D: is the DMA channel and Q: is the IRQ setting


GALANT
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1

        CONFIG.SYS
        NONE


GALAXY - See Multi-Media Pro 16


GATEWAY 2000 AUDIO DRIVE
        AUTOEXEC.BAT
        C:\G2KAUDIO\UTILITY\GWBVOL
        SET BLASTER=A220 I5 D1 T5
        SET SOUND=C:\G2KAUDIO

        CONFIG.SYS
        NONE

This sound card will autoconfigure itself to Soundblaster or Microsoft
Sound System mode.


GOLDEN SOUND BY TOPEK
        AUTOEXEC.BAT
        C:\GS16\GS-ENV PC:\GS16ES

        CONFIG.SYS
        NONE


GRAVIS ULTRASOUND OR GRAVIS ACE
        AUTOEXEC.BAT
        SET ULTRASND=*
        SET ULTRADIR=*
        C:\ULTRASND\ULTRINIT
        SBOS.BAT**
        SET BLASTER=A220 I5 D1

        CONFIG.SYS
        NONE

*Check the AUTOEXEC.BAT on your hard drive for complete SET lines for the GUS.
**The SBOS.BAT line must be loaded to enable the card's Soundblaster
emulation. This line is not needed for the ACE.


IBM PS/1
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1

        CONFIG.SYS
        NONE


ISP 16
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        SET ISP16=C:\ISP16
        C:\ISP16\ISPINIT /B/M*

        CONFIG.SYS
        NONE
*Use /B switch for SB mode
*Use /M switch for  Microsoft Sound System mode



JAZZ 16
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1

        CONFIG.SYS
        DEVICE=C:\JAZZ\JAZZ.SYS D:* Q:*

*D:  DMA CHANNEL.
*Q:  IRQ SETTING.
Specific values and directories may change



MAD 16
        AUTOEXEC.BAT
        SET MAD16=C:\MAD16
        SET BLASTER=A220 I5 D1 
        C:\MAD16\M16INIT /B /M*

        CONFIG.SYS
        NONE

*Use /B switch for Soundblaster  mode.  Use /M switch for Microsoft Sound
System Mode



MAGIC S20 - Common on Acers
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        SET SOUND16=C:\MAGICS20
        C:\MAGICS20\SNDINIT /B /M*

        CONFIG.SYS
        NONE

*Use /B switch for Soundblaster  mode.  Use /M switch for  Microsoft Sound
System Mode



MAGITEC GREEN 16
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1

        CONFIG.SYS
        NONE



MEDIA CONCEPT
        AUTOEXEC.BAT
        SET MC=C:\MC

        CONFIG.SYS
        NONE



MEDIA VISION DELUXE
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        C:\MEDVSN\VBEAI.COM

        CONFIG.SYS
        DEVICE=C:\MEDVSN\PROS.SYS



MEDIA VISION PREMIUM 3D SCSI2
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1

        CONFIG.SYS
        DEVICE=C:\MEDVSN\PA3D.SYS
        DEVICE=MINI406A.SYS



MMCD16W
        AUTOEXEC.BAT
        SET BLASTER=*
        SET SOUND=C:\MMCD16W
        SET GALAXY=*

        CONFIG.SYS
        NONE

*Check the AUTOEXEC.BAT for the SET BLASTER and SET GALAXY parameters



MONTE CARLO BY TURTLE BEACH
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        C:\MCARLO\MCHKMIX

        CONFIG.SYS
        DEVICE=C:\MCARLO\MCMODE -S -W*

*Use -S switch for SB mode
*Use -W switch for  Microsoft Sound System Mode



MOZART SOUND CARD Common on Canons
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        SET SOUND=C:\MOZART
        C:\MOZART\MTZVOL.EXE

        CONFIG.SYS
        DEVICE=C:\MOZART\MZTINIT.SYS WSS /530*

*WSS /530 Puts the card into WSS mode port 530



MULTI-MEDIA PRO 16
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        SET GALAXY=*
        SET SOUND=C:\MMP16P

        CONFIG.SYS
        NONE

*Check the AUTOEXEC.BAT on your hard drive for the full SET GALAXY line.



MW WAVE - Common on IBM Thinkpads
        AUTOEXEC.BAT
        SET BLASTER=
        SET MWPATH=C:\MWD\MANAGER;C:\MWD\MWGAMES*
        SET MWROOT=C:\MWD
        MWGAMES=ON**

        CONFIG.SYS
        NONE

*This is all one line.
**ON turns on Soundblaster emulation and OFF turns it off.



ORCHID GAMEWAVE
        AUTOEXEC.BAT
        SET BLASTER=*
        SET SOUND=*
        C:\GW32\GW32.EXE

        CONFIG.SYS
        NONE

*Check the AUTOEXEC.BAT on your hard drive for the complete SET SOUND and
SET BLASTER lines.



ORCHID SOUNDWAVE
        AUTOEXEC.BAT
        SET BLASTER=*
        SET SOUND=*
        C:\SW32\SW32.EXE

        CONFIG.SYS
        NONE

*Check the AUTOEXEC.BAT on your hard drive for the complete SET SOUND and
SET BLASTER lines.



PHILLIPS
        AUTOEXEC.BAT
        NONE

        CONFIG.SYS
        NONE



PRO AUDIO SPECTRUM 16
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1

        CONFIG.SYS
        DEVICE=C:\SPECTRUM\MVSOUND.SYS D:*Q:*

*D:  DMA CHANNEL.      Q:  IRQ SETTING.
<DIR> may be PROAUDIO on older drivers.



PRO SONIC
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1

        CONFIG.SYS
        DEVICE=C:\PROSONIC\PROSYS.SYS



SC400
        AUTOEXEC.BAT
        SET SOUND=C:\SC400
        SET BLASTER=A220 I5 D1
        C:\SC400\UTILITY\SNDINIT /B

        CONFIG.SYS
        NONE



SGBAS16
        AUTOEXEC.BAT
        SET BLASTER=*
        SET SOUND=C:\SGBAS16
        SET GALAXY=*

        CONFIG.SYS
        DEVICE=C:\SGBAS16\DRIVERS\EEPRO.SYS

*Check the AUTOEXEC.BAT on your hard drive for the complete SET GALAXY and
SET BLASTER lines.



SOUNDBLASTER AWE 32 
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        SET SOUND=C:\SB16
        C:\SB16\SB16SET /P/Q
        C:\SB16\DIAGNOSE /S*
        C:\SB16\AWEUTIL /S

        CONFIG.SYS
        DEVICE=C:\SB16\DRV\CTSB16.SYS   /UNIT=0 /BLASTER=A:220 I:5 D:1 H:5
        DEVICE=C:\SB16\DRV\CTMMSYS.SYS**

*May be SBCONFIG on older cards.
**This line is only required to enable the sound card's CD-ROM interface.



SOUNDBLASTER PRO
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        SET SOUND=C:\SBPRO*
        C:\SBPRO\SBP_SET*

        CONFIG.SYS
        NONE

*On newer cards the drivers and such may look like 
the SB16 except loading out of a different directory.



SOUNDBLASTER 16
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1 H5 T6
        SET SOUND=C:\SB16
        SET MIDI=SYNTH:1 MAP:E
        C:\SB16\SB16SET*
        C:\SB16\DIAGNOSE /S**

        CONFIG.SYS
        DEVICE=C:\SB16\DRV\CTSB16.SYS /UNIT=0 /BLASTER=A:220 I:5 D:1 H:5
        DEVICE=C:\SB16\DRV\CTMMSYS.SYS***

*Check the AUTOEXEC.BAT on your hard drive for the complete SB16SET line.




SOUND EXPRESSION BY BOCA
        AUTOEXEC.BAT
        SET BLASTER=
        C:\CE1440\CSACMAX1.COM*
        C:\CE1440\CSACHMX1.COM**

        CONFIG.SYS
        DEVICE=C:\SE1440\CSACMOD1.EXE -S -W***

*Enables Soundblaster compatibility.
**/ON turns on Soundblaster compatibility, /OFF turns it off.
***-S for Soundblaster mode and -W for Windows Sound System mode.




SOUND EZ - See Mad 16



SOUND FX PLUS
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        SOUND=C:\MMSUP

        CONFIG.SYS
        NONE




SOUNDMAND BY LOGITECH
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1

        CONFIG.SYS
        DEVICE=C:\SOUNDMAN\MVSOUND.SYS




SOUND 16A - Common on Packard Bells 1 OF 2**
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        SET GALAXY=*
        C:\SOUND16A\UTILITY\SETMODE /MSS**
        SET SOUND16=C:\SOUND16A

        CONFIG.SYS
        NONE

*Check the AUTOEXEC.BAT on your hard drive for the complete SET GALAXY line.
**Use /SB switch for SB mode. Use /MSS switch for Microsoft Sound System Mode.




SOUND 16A - Common on Packard Bells 2 OF 2**
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        SET GALAXY=*
        C:\AUDIO\SNDINIT.EXE /B**
        SET SOUND16=C:\AUDIO

        CONFIG.SYS
        NONE

*Check the AUTOEXEC.BAT on your hard drive for the complete SET GALAXY line.
**Use /B switch for SB mode
**Use /M switch for  Microsoft Sound System Mode




SOUND 144 - Common on Packard Bells
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        SET GALAXY=*
        SET SOUND=SOUND144
        C:\SOUND144\UTILITY\SETMODE /SBP**

        CONFIG.SYS
        NONE

*Check the AUTOEXEC.BAT on your hard drive for the complete SET GALAXY line.
**Use /SBP for Soundblaster mode and /MSS for Microsoft Sound System mode.




STRAUSS
        AUTOEXEC.BAT
        NONE

        CONFIG.SYS
        NONE





TROPEZ BY TURTLE BEACH 
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        C:\TROPEZ\DOSAPPS\SETUPSND*
        C:\TROPEZ\DOSAPPS\TZMODE -S*

        CONFIG.SYS
        DEVICE=C:\TROPEZ\DOSAPPS\TZMODE**

*Windows will disable these lines, so they will need to be run again
if Windows is started and shut down.  Use -S for Soundblaster mode and -W
for Windows Sound System mode on the TZMODE line.
**This line is necessary if the sound card is also 
acting as the CD-ROM controller.




VIBRA 16
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1 H5 T6
        SET SOUND=C:\VIBRA16
        SET MIDI=*
        C:\VIBRA16\DIAGNOSE /S**
        C:\VIBRA16\MIXERSET /P/Q

        CONFIG.SYS
        DEVICE=C:\VIBRA16\DRV\VIBRA16.SYS
        DEVICE=C:\VIBRA16\DRV\CTMMSYS.SYS

*Check the AUTOEXEC.BAT on your hard drive for the complete SET MIDI line.
**Older cards may use SBCONFIG instead of DIAGNOSE.




VOYETRA SOUND
        AUTOEXEC.BAT
        SET BLASTER=A220 I5 D1
        SET ISP16=ISP16*
        C:\ISP16\ISPINIT /B

        CONFIG.SYS
        NONE

*May be SET ISP16=VOYETRA




WAVERIDER BY AZTECH
        AUTOEXEC.BAT
        SET BLASTER=
        SET SOUND=C:\WAVRIDER
        SET GALAXY=
        C:\WAVRIDER\DRIVERS\WAVERIDE.EXE
        C:\WAVRIDER\SETMODE /SBP*

        CONFIG.SYS
        NONE

*Use /SBP for Soundblaster mode and /MSS for Microsoft Sound System mode.


